Home » Shop » Handheld Hydraulic Cut-off Saw | 9.5″ Cutting Depth | 24″ BladeManuals

Sealey PBI2212GS RoadStart Emergency Jump Starter 12 volt 2300 Peak Amps

$ 99.87

Category:
Visit Stockist to see if FREE SHIPPING IS INCLUDED The Sealey PBI2212GS is a professional grade, high performance AGM battery, specially formulated to jump-start vehicles. This unit is DERKA approved and includes an automatic maintenance charger with patented microprocessor controlled speed charging and thermal runaway protection. This combined with an isolating on/off switch, digital display showing the internal battery level and the vehicle battery voltage, and a 2300 peak Amp output makes this a very capable jump starter.A fusible link integrated in the output cable provides surge and spike protection, preventing damage to delicate and sophisticated vehicle electronics as well as the booster with heavy-duty clamps with a braided link between each jaw for maximum power transmission, and curved to allow easy access to awkward or hard-to-reach battery terminals. This model is also equipped with Audible warning system (AWS) signals if the unit has been turned on for too long without being connected to a battery.Completing the PBI2212GS is a handy 2.1A USB port ideal for charging phones or tablets and Sealey’s trademark build quality for ensured reliability. Starting Current: 900APeak Amps: 2300AVoltage: 12VAuxiliary Output: 12VCable & Clamp Length: 1.59mWeight: 9.5kg

FAQs

What are the blade requirements for this saw?

Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.

  1. Use blades that meet applicable industrial safety code specifications.
  2. Use blades that are approved by the blade manufacturer for the material to be cut.
    Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations.
  3. Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
  4. Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.

What are the hydraulic power source requirements for this saw?

The hydraulic power source must meet the following design criteria:

  1. The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
    cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
    injury.
  2. The hydraulic power source must meet the hydraulic requirements found in the product manual.

What type of maintenance is required for this saw?

Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.

 

 

Specifications

HydraSaws
ModelS14S16S20S24
Part #2001400200160020020002002400
Blade Size14 in. (35.5 cm)16 in. (40.6 cm)20 in. (50.8 cm)24 in. (61.0 cm)
Cutting Depth5.25 in. (13.3 cm)6 in. (15.2 cm)7.5 in. (19 cm)9.5 in. (24 cm)
Blade Speed4100 rpm2750 rpm1830 rpm1455 rpm
Flow5-8 gpm (20-30 lpm)5-8 gpm (20-30 lpm)5-8 gpm (20-30 lpm)5-8 gpm (20-30 lpm)
Pressure Range2000 – 2500 psi (138 – 172 bar)2000 – 2500 psi (138 – 172 bar)2000 – 2500 psi (138 – 172 bar)2000 – 2500 psi (138 – 172 bar)
Weight28 lbs. (12.7 kg)39 lbs. (17.7 kg)52 lbs. (23.6 kg)54 lbs. (24.5 kg)

Manuals

Related products

Cart