Clarke JumpStart 1224 Dual Voltage 12 volt and 24 Volt
$ 90.85
Visit Stockist to see if FREE SHIPPING IS INCLUDED The versatile Jumpstart 1224 has the power to start engines requiring 12 or 24 Volts using 2x22Ah batteries.Simply switch to the required voltage and connect the 1 metre cables to deliver up to 1000A of current at 12 Volts or 500A at 24Volts. This feature-rich unit includes a 5-bulb worklight, audible warning when incorrectly connected and low battery alarm.The jumpstart charges from mains and 12V with the adaptors provided so you can always be sure that it is ready when you need it and also has a 12V DC outlet to power electrical devices while on the move. Starting boost output of 1000A at 12V and 500A at 24V and peak output of 2000A at 12V and 1000A at 24VStarts petrol engines up to 6 litres and diesel engines up to 3 litresLED battery status indicators and built-in 5 bulb lamp for an extra bright work lightAudible incorrect polarity and low battery alarmIncludes 230V mains charger and 12V adaptor for in-vehicle chargingGripped carry handle and booster cable storage facilitySwitchable dual voltage. 12V & 24V for extra heavy duty usage
FAQs
What are the blade requirements for this saw?
Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.
- Use blades that meet applicable industrial safety code specifications.
- Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations. - Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
- Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.
What are the hydraulic power source requirements for this saw?
The hydraulic power source must meet the following design criteria:
- The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury. - The hydraulic power source must meet the hydraulic requirements found in the product manual.
What type of maintenance is required for this saw?
Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.
Specifications
| HydraSaws | ||||
|---|---|---|---|---|
| Model | S14 | S16 | S20 | S24 |
| Part # | 2001400 | 2001600 | 2002000 | 2002400 |
| Blade Size | 14 in. (35.5 cm) | 16 in. (40.6 cm) | 20 in. (50.8 cm) | 24 in. (61.0 cm) |
| Cutting Depth | 5.25 in. (13.3 cm) | 6 in. (15.2 cm) | 7.5 in. (19 cm) | 9.5 in. (24 cm) |
| Blade Speed | 4100 rpm | 2750 rpm | 1830 rpm | 1455 rpm |
| Flow | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) |
| Pressure Range | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) |
| Weight | 28 lbs. (12.7 kg) | 39 lbs. (17.7 kg) | 52 lbs. (23.6 kg) | 54 lbs. (24.5 kg) |
Manuals
Related products
- Add to cart
- Select options This product has multiple variants. The options may be chosen on the product page
- Select options This product has multiple variants. The options may be chosen on the product page
- Select options This product has multiple variants. The options may be chosen on the product page
Sealey Powerstart POWERSTART900 Jump Starter and Power Pack 12 volt or 24 volt
Sealey RS105 12 volt and 24 volt RoadStart Emergency Jump Starter
Clarke JumpStart 910 with 12 volt Air Compressor