Clarke JumpStart 4000 Heavy Duty 1500 Amps peak output and 700 Amps boost

$ 96.82

Category: Outdoor Cooking

Visit Stockist to see if FREE SHIPPING IS INCLUDED Full product description HEAVY DUTY equipped with ‘extra-power’ battery, perfect for starting bigger engines.Selected as a ?Best Buy? by Which Caravan Magazine because of its feature packed specification.It is ideal for starting petrol engines up to 6 litre and diesels up to 4 litre. Included are 1m long leads for easier use, allowing you to safely connect the Jumpstart 4000 to your battery. The audible alarm will warn you if you have incorrectly attached the leads to avoid damage while the internal battery is maintenance free and has a low charge indicator. 1500 Amps peak output / 700 Amps boost at 12VSealed, maintenance free battery for long service life & safe operationBattery condition & charge level indicatorIntegral worklight for roadside repairs or emergency situationsBattery pack can be recharged from 230V mains or in vehicle via 12V adapterHeavy Duty 1m long leads & heavy duty battery clampsWeighs an impressive 17kg due to the top quality, long life battery

FAQs

What are the blade requirements for this saw?

Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.

Use blades that meet applicable industrial safety code specifications.
Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations.
Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.

What are the hydraulic power source requirements for this saw?

The hydraulic power source must meet the following design criteria:

The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury.
The hydraulic power source must meet the hydraulic requirements found in the product manual.

What type of maintenance is required for this saw?

Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.

Specifications

HydraSaws
Model	S14	S16	S20	S24
Part #	2001400	2001600	2002000	2002400
Blade Size	14 in. (35.5 cm)	16 in. (40.6 cm)	20 in. (50.8 cm)	24 in. (61.0 cm)
Cutting Depth	5.25 in. (13.3 cm)	6 in. (15.2 cm)	7.5 in. (19 cm)	9.5 in. (24 cm)
Blade Speed	4100 rpm	2750 rpm	1830 rpm	1455 rpm
Flow	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)
Pressure Range	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)
Weight	28 lbs. (12.7 kg)	39 lbs. (17.7 kg)	52 lbs. (23.6 kg)	54 lbs. (24.5 kg)