Laser 7405 Jump Starter – Multi-Function Diesel Engines 3.5 Litre Petrol Engines 4.5 Litre

$ 98.38

Category: Outdoor Cooking

Visit Stockist to see if FREE SHIPPING IS INCLUDED Surprisingly small, but packs a powerful punch! The new Multi-function Jump Starter from Laser Tools (part number 7405) is an efficient and extremely compact emergency engine starting power pack. Packed full of features, it also features a bright LED to illuminate the work area, (flashing mode can be used as an emergency beacon), two USB outputs (for charging mobile phones, etc), a Type-C input/output port and a digital voltage display on the cable clamp adaptor. The unit and accessories are supplied in a convenient and protective case.The unit is charged from a suitable USB port on a PC, taking approximately three hours to fully charge. As it charges, the power/charging LED display will cycle through the four LEDs. Once fully charged, the LED display shows four indicator lights ON.To jump start a car with a flat battery, simply connect up the cable clamp adaptor to the jump starter, connect the clamps to the car?s battery and start the car.The jump starter is equipped with two USB ports that are suitable for charging and powering mobile phones, tablets, etc. Output 1 is a USB QC 3.0 rated port (3.6V ? 12V; 1.5A ? 3A). Output 2 is a standard USB port (5V 2.1A). These are used with the multi-function lead which includes the following device connectors: USB, 2 x Type C and a micro-USB. Port 7 is a Type C input/output port which is used when charging the device but can also output (5V / 3A).Don?t let the small size fool you, the Multi-function Jump Starter will start diesel engines up to 3.5 litres and petrol engines up to 4.5 litres. It is a remarkably versatile and very powerful little jump starter 2 USB ports includes smart jumper clamps and 2 in 2 USB cableCapacity 7200mAh will start diesel engines up to 3.5L and petrol engines up to 4.5L.Can also be used as a power bank for a laptop/phoneIncludes 2 USB ports, 2 to 2 USB cable and 2 smart jumper clamps.Start current 350A, peak current 700A, charging time approx. 3 hours with charging indicator.Short circuit, overcharge, discharge, low voltage, reverse polarity protection.Supplied with a storage/carrying case.

FAQs

What are the blade requirements for this saw?

Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.

Use blades that meet applicable industrial safety code specifications.
Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations.
Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.

What are the hydraulic power source requirements for this saw?

The hydraulic power source must meet the following design criteria:

The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury.
The hydraulic power source must meet the hydraulic requirements found in the product manual.

What type of maintenance is required for this saw?

Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.

Specifications

HydraSaws
Model	S14	S16	S20	S24
Part #	2001400	2001600	2002000	2002400
Blade Size	14 in. (35.5 cm)	16 in. (40.6 cm)	20 in. (50.8 cm)	24 in. (61.0 cm)
Cutting Depth	5.25 in. (13.3 cm)	6 in. (15.2 cm)	7.5 in. (19 cm)	9.5 in. (24 cm)
Blade Speed	4100 rpm	2750 rpm	1830 rpm	1455 rpm
Flow	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)
Pressure Range	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)
Weight	28 lbs. (12.7 kg)	39 lbs. (17.7 kg)	52 lbs. (23.6 kg)	54 lbs. (24.5 kg)