Clarke JSM300 Multifunction Micro Jumpstart and Portable Device Charger Power Pack

$ 99.23

Category: Outdoor Cooking

Visit Stockist to see if FREE SHIPPING IS INCLUDED Multifunction Micro Jump Start Portable device charger 12AhThis amazingly small and lightweight portable lithium – ion power bank with inbuilt torch weights only 500g (without leads). It will jump start a flat car battery making it perfect for emergency situations. In addition it provides USB 5V device charging for mobile phones, cameras etc. plus 12V accessory and 19V laptop computer power outputs. An ideal device to keep in your vehicle. Can be used approx. 20 times on a single charge (depends on age and condition of battery)Vehicle jumpstart output: Starting current 300A, Peak current 500A12Ah Lithium ion batteries with very low charge cycle requiring only approx 6monthly recharge if not used.Powerful 1W LED torch12V vehicle jumpstart output with LED connection status smart lead2 x 5V USB output with 4-in-1 device adaptor cable; 30pin dock (apple), Lightening (apple), mini and micro USB to suit most mobile phone connectorsSelectable 12V/10A and 19V/3.5A dc outputs with 8 adaptor plugs for use with laptop computers and other devices/accessoriesIncludes vehicle aux power outlet (cigarette lighter) and mains chargersSupplied in convenient zipped storage bag

FAQs

What are the blade requirements for this saw?

Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.

Use blades that meet applicable industrial safety code specifications.
Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations.
Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.

What are the hydraulic power source requirements for this saw?

The hydraulic power source must meet the following design criteria:

The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury.
The hydraulic power source must meet the hydraulic requirements found in the product manual.

What type of maintenance is required for this saw?

Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.

Specifications

HydraSaws
Model	S14	S16	S20	S24
Part #	2001400	2001600	2002000	2002400
Blade Size	14 in. (35.5 cm)	16 in. (40.6 cm)	20 in. (50.8 cm)	24 in. (61.0 cm)
Cutting Depth	5.25 in. (13.3 cm)	6 in. (15.2 cm)	7.5 in. (19 cm)	9.5 in. (24 cm)
Blade Speed	4100 rpm	2750 rpm	1830 rpm	1455 rpm
Flow	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)
Pressure Range	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)
Weight	28 lbs. (12.7 kg)	39 lbs. (17.7 kg)	52 lbs. (23.6 kg)	54 lbs. (24.5 kg)