Ford Mustang Ignition H75 key blank 1996 1997
$ 97.62
Description Square-ended JMA brand ignition / door key for any 1996 or 1997 Ford Mustang and other similar era Ford, Lincoln & Mercury vehicles. Note this is a non-transponder mechanical key, so can’t be programmed. Cross reference with Strattec 322789, Ilco 1196FD, H75. Should also fit (but check your existing key carefully): 1996-1999 FORD 6000 1996-1999 FORD 9000 1996-1997 FORD AEROSTAR 1996 FORD BRONCO 1996-1999 FORD CF7000 1996-2006 FORD CLUB WAGON 1997 FORD CROWN VICTORIA 1996-2005 FORD ECONOLINE 1996-1998 FORD EXPLORER 1996-1998 FORD F-150 1996-1998 FORD F-250 1996-1998 FORD F-350 1996-2010 FORD F-450 1996-2010 FORD F-550 1996-2010 FORD F-650 1996-2010 FORD F-750 1996-1998 FORD RANGER 1996-1999 FORD TAURUS 1996-1998 FORD THUNDERBIRD 1996-2000 FORD WINDSTAR 1997-1998 LINCOLN CONTINENTAL 1996-1997 MAZDA B-SERIES PICKUP 1997-1998 MERCURY COUGAR 1997 MERCURY GRAND MARQUIS 1997 MERCURY MOUNTAINEER 1997-1998 MERCURY SABLE 1996-2002 MERCURY VILLAGER
FAQs
What are the blade requirements for this saw?
Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.
- Use blades that meet applicable industrial safety code specifications.
- Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations. - Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
- Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.
What are the hydraulic power source requirements for this saw?
The hydraulic power source must meet the following design criteria:
- The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury. - The hydraulic power source must meet the hydraulic requirements found in the product manual.
What type of maintenance is required for this saw?
Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.
Specifications
| HydraSaws | ||||
|---|---|---|---|---|
| Model | S14 | S16 | S20 | S24 |
| Part # | 2001400 | 2001600 | 2002000 | 2002400 |
| Blade Size | 14 in. (35.5 cm) | 16 in. (40.6 cm) | 20 in. (50.8 cm) | 24 in. (61.0 cm) |
| Cutting Depth | 5.25 in. (13.3 cm) | 6 in. (15.2 cm) | 7.5 in. (19 cm) | 9.5 in. (24 cm) |
| Blade Speed | 4100 rpm | 2750 rpm | 1830 rpm | 1455 rpm |
| Flow | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) | 5-8 gpm (20-30 lpm) |
| Pressure Range | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) | 2000 – 2500 psi (138 – 172 bar) |
| Weight | 28 lbs. (12.7 kg) | 39 lbs. (17.7 kg) | 52 lbs. (23.6 kg) | 54 lbs. (24.5 kg) |
Manuals
Related products
- Add to cart
- Select options This product has multiple variants. The options may be chosen on the product page
- Select options This product has multiple variants. The options may be chosen on the product page
- Select options This product has multiple variants. The options may be chosen on the product page
Ford Mustang Ignition & Trunk Pony key blank set 1965 1966
GM 95-99 key blank GM25 GM30 B83 B89
Ford Mustang Trunk / Boot key blank 1967 – 1993