Audemars Piguet Royal Oak Stainless Steel Black Dial 3120 Swiss Super Clone Watch Ref-15400ST.OO.1220ST.01.A

$ 98.48

Category: Outdoor Cooking

MOVEMENTMovement : Audemars Piguet Swiss 3120 Automatic, Exact 1:1 Super Clone Every Internal Component Mirrors the Original Audemars Piguet 3120 Movement, Complete with Engraved Branding and Serial NumbersFunctions : Hours, Minutes, Centre Seconds and DateNumber of parts : 257Jewels : 40Frequency : 4 hz 28,800 vphPower reserve : Approximately 60 HoursWater Resistance : Up to 50 MetersCASEMaterial : 904L Stainless SteelDiameter : 41mm (Accurate Size of Genuine Watch)Thickness : 10.5 mmWinding Crown : Screw-LockedBack Case : Glareproofed Sapphire Crystal Transparent Back Case Which Gives Clear Visibility of Inner Mechanism MovementCrystal : Glareproofed Scratch-Resistant SapphireBRACELETMaterial : 904L Stainless SteelType : AP Folding Clasp (Accurate Size of Genuine Watch)DIALColor : Black with “Grande Tapisserie” PatternMarkers : Time Marking in Long-Lasting Luminescent Which Glow in Dark EnvironmentWARRANTY Warranty : 2 Years

FAQs

What are the blade requirements for this saw?

Any blade from your supplier must meet the following design criteria. Using blades on this saw that don’t meet these requirements can cause equipment damage and/or personal injury.

Use blades that meet applicable industrial safety code specifications.
Use blades that are approved by the blade manufacturer for the material to be cut.
Use approved dry cutting type blades in dry cutting operations and approved wet cutting type blades in wet cutting operations.
Do not exceed the maximum operating speed of 1830 rpm for the S20, 1455 rpm for the S24, or the blade manufacturer’s rated speed. Blades must be speed tested to ANSI B7.1 safety code specifications.
Always use blades with mounting blotters on both sides when using abrasive blades. Remove the drive pin from the arbor flange before mounting an abrasive blade.

What are the hydraulic power source requirements for this saw?

The hydraulic power source must meet the following design criteria:

The flow must not exceed 8 GPM, and the pressure relief valve must not exceed 2500 psi. Failure to comply could
cause excessive blade rpm and/or overpressurizing the system, resulting in equipment damage and/or personal
injury.
The hydraulic power source must meet the hydraulic requirements found in the product manual.

What type of maintenance is required for this saw?

Inspect the blade mounted on the saw. Remove and destroy the blade if any cracks, chips, gouges, or loose or missing segments are present. Failure to do this can cause personal injury.

Specifications

HydraSaws
Model	S14	S16	S20	S24
Part #	2001400	2001600	2002000	2002400
Blade Size	14 in. (35.5 cm)	16 in. (40.6 cm)	20 in. (50.8 cm)	24 in. (61.0 cm)
Cutting Depth	5.25 in. (13.3 cm)	6 in. (15.2 cm)	7.5 in. (19 cm)	9.5 in. (24 cm)
Blade Speed	4100 rpm	2750 rpm	1830 rpm	1455 rpm
Flow	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)	5-8 gpm (20-30 lpm)
Pressure Range	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)	2000 – 2500 psi (138 – 172 bar)
Weight	28 lbs. (12.7 kg)	39 lbs. (17.7 kg)	52 lbs. (23.6 kg)	54 lbs. (24.5 kg)